About PrintCost.site

Last updated

PrintCost.site is a free 3D print cost calculator that runs entirely in your browser. You type your slicer's print time and filament weight, or drop in an STL, OBJ or 3MF file, and it prices the job as you type: filament, electricity, machine wear, labor, a failure buffer and your markup. Your file is opened on your own device and stays there, and you can start pricing as soon as the page loads.

Who makes it

PrintCost.site is built and maintained by Studio Reidel. Questions, corrections and bug reports go to support@printcost.site.

How the estimates work

Every figure in a quote is computed in your browser by one pricing engine, in a fixed order that the pricing guide walks through. Each step is rounded to the currency's smallest unit as it is made and taken from the figure before it as printed, so the lines of a quote add up by hand to the price it shows.

If you type the print time and filament weight from your slicer, or drop in a 3MF that Bambu Studio or OrcaSlicer has already sliced, those numbers are used as they are. If you drop in an STL, an OBJ or an unsliced 3MF instead, the calculator has to estimate them from the mesh, and it assumes:

  • 15% infill, with walls 0.84 mm thick: the settings of the stock 0.20 mm Standard profile, which put a file's weight typically within about 4% of what OrcaSlicer 2.4.2 reports. An unsliced 3MF saved by Bambu Studio or OrcaSlicer states its own infill, wall count and layer height, and the estimate uses those instead; if it turns supports on, they are added from the area that faces down off the bed.
  • A print time from the model's shape: 7 minutes to heat and level, then time for its outer shell, its infill and every layer of its height. It is fitted to what OrcaSlicer 2.4.2 reports for a Bambu Lab A1 on the 0.20 mm Standard profile, and on 116 sliced models it typically lands within about 5% of the slicer's time. Pick your printer on the job ticket and the time is fitted the same way to that printer's own stock profile: a P1S or an X1 Carbon prints the same part about 28% faster than the A1. A 3MF with several plates is timed plate by plate, each with its own setup and layers, and the job ticket can price one plate alone.
  • Each material's own density, as OrcaSlicer's stock Bambu filaments give it (PLA 1.26, PETG 1.25, ABS 1.04, ASA 1.05, TPU 1.22 g/cm³), so the same file weighs about 17% less in ABS than in PLA.

That is why your slicer's own weight and time are always the more precise input: it counts your supports and every other setting, where the calculator reads at most a 3MF's infill, walls and layer height. The 3MF cost calculator lists what it reads from a project and what it does not.

The rates (a filament price for each material, electricity, machine wear, labor, the failure buffer, the markup and the minimum charge) start at values written for each currency and are yours to edit. There is no exchange-rate conversion, because a rate in one currency means nothing in another.

Where the example numbers come from

The prints on the cost page are real models. Each was sliced in OrcaSlicer 2.4.2 for a Bambu Lab A1 on the stock 0.20 mm Standard profile in Bambu PLA Basic, on 28 September 2026, and its weight and time are the slicer's own totals, not estimates. Every model is credited to its creator with a link. The page prices them with the same engine as the calculator, so its figures cannot drift from it.

What it does not do

  • Every figure is an estimate. Your printer, settings and filament decide the real cost.
  • It prices FDM printing, not resin printing or outsourced print services.
  • It has no tax or marketplace-fee math, and shipping is a flat amount you set.

Privacy

Your files never leave your device, and the only third-party script is aggregate analytics from Vercel. The privacy policy lists exactly what is stored on your device.

If a number looks wrong

Email support@printcost.site with the print time, weight, material and rates you used, and what you expected to see.

← Back to the calculator